manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

1.3

Removing and installing the steering

column trim panel

Removing
– Remove driver's airbag unit

⇒ “3.13 Removing and installing driver airbag unit”,

page 233

 .

– Remove the steering wheel

⇒ “3.12 Summary of components of steering wheel”,

page 232

 .

– Slacken the fixing lever of the steering wheel adjustment.
– Pull out the steering column and press it down.
– Loosen the frame with the top part of the steering column trim

panel -1- from the supports.

– Remove the top part of the steering column trim panel -1-.

– Release the screws from the bottom part of the steering col‐

umn trim panel - 1 - (1.5 Nm).

– Loosen the bottom part of the steering column trim panel -2-

from the supports.

Installing
– The installation occurs in reverse order.

1.4

Removing and installing the decorative trim of the dash panel

Removing
– Remove vent ⇒  Heating, Air Conditioning; Rep. gr.  87 .
– Unscrew screws -1-.
– Carefully unclip the decorative trims - 2 and 3 - with e.g. a

dismantling wedge -3309- .

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Dash panel    

251

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Brand: Mazda Pages: 4
Baja Designs S8 Instructions Manual preview
S8
Brand: Baja Designs Pages: 6
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Vintage Air 561163 Manual preview
561163
Brand: Vintage Air Pages: 28
Whispbar K934W Fitting Instructions Manual preview
K934W
Brand: Whispbar Pages: 15
MAcarbon Ferrari 360 Map Carbon Light Installation Instructions preview
Ferrari 360 Map Carbon Light
Brand: MAcarbon Pages: 4
METRON PC05T User Manual preview
PC05T
Brand: METRON Pages: 4
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Brand: Over Armour Offroad Pages: 9
Safe Fleet PRIME DESIGN VRR3-FT21G-ST Manual preview
PRIME DESIGN VRR3-FT21G-ST
Brand: Safe Fleet Pages: 12
RAM 2013 2500 Big Horn Information preview
2013 2500 Big Horn
Brand: RAM Pages: 12
Westin 32-1660 Instructions preview
32-1660
Brand: Westin Pages: 3
Kuda 076100 Installation Instruction preview
076100
Brand: Kuda Pages: 3
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Brand: AUTOTECH Pages: 4
APS iBoard IB-R159 Manual preview
iBoard IB-R159
Brand: APS Pages: 4
SIXTOL DRY CAR Instructions For Use Manual preview
DRY CAR
Brand: SIXTOL Pages: 32
Vauxhall MasterFit Manual preview
MasterFit
Brand: Vauxhall Pages: 4
Cadillac CTS 2011 Manual preview
CTS 2011
Brand: Cadillac Pages: 78
Curt Manufacturing 58987 Installation Manual preview
58987
Brand: Curt Manufacturing Pages: 4

Brands by name

Popular brands

Load more brands