Skoda Rapid NH 2014 Page 195 Workshop Manual Download

Page: 195 / 319

3.5

Cover strip of wing

3.5.1

Installation instructions for cover strip of

wing

Note

♦

Use only the glue remover - D 002 000 10- .

♦

Make sure that the adhesive surfaces are free from dust and

grease.

♦

The cover trip must be glued on immediately after cleaning.

♦

Remove protective foil from its wrapping until just before as‐

sembly.

♦

The processing temperature is about 21 ℃.

3.5.2

Removing and installing cover strip of wing

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Strips and trims

187

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands