Skoda Rapid NH 2014 Workshop Manual Download

Page: 42 / 319

– If the screws -2- are loosened, the front flap lock -1- can be

adjusted to the front flap laterally -arrow a- and in height

-arrow b- ⇒ Body Repairs; Rep. gr. 00 ; body gaps; front body .

– Tightening torque of screws -2- (12 Nm).

1.10.2

Adjusting the locking clamp

– Release screws - 3 -.
– The locking clamp -1- can now be adjusted in the oversized

holes.

– Tightening torque of screws -3- (10 Nm).

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

Rep. gr.55 - Bonnet, rear lid

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands