Skoda Rapid NH 2014 Page 101 Workshop Manual Download | Manualshive

Page: 101 / 319

background image

Note

♦

To adjust the locking clamp -2- once the screws -3- are loosened, increased force must be applied.

♦

When closing the door it must lock completely without using additional force and must have no play.

♦

When adjusting the locking clamp, the door must not be pressed upwards or downwards.

The locking clamp is used for adjusting the following:
• If the rear door adjustment is not flush with the side part.
Carry out the following tasks
– Slacken the locking clamp -1- by loosening the screws -2- at

the C pillar.

– Adjust the door with the locking clamp -1- in such a way that

the rear door when in the closed state is flush with the side

part (wind noise).

– Tighten screws - 2 - of locking clamp - 1 -.
Tightening torque of screws (Pos. 2) - 20 Nm.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Rear door

93

«
...
99
100
101
102
103
...
»

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Brand: VanEssa mobilcamping Pages: 8

Brand: Jeep Pages: 673

Brand: TATA Motors Pages: 156

Brand: Ironton Pages: 7

Brand: Yutrax Pages: 8

Brand: Hudson Pages: 34

Brand: Quadratec Pages: 14

Brand: Subaru Pages: 540

Brand: TOPPOINT Pages: 2

Brand: Honda Pages: 268

Brand: Jeep Pages: 374

Brand: Master Tailgaters Pages: 10

Multi Vehicle Mount MVM-35-05

Brand: Bracketron Pages: 4

DH-RB 05.02 Series

Brand: Dhollandia Pages: 65

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: MayPole Pages: 3

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

HFC7151M1V-U221B

Brand: JAC Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands