Skoda Rapid NH 2014 Workshop Manual Download

Page: 87 / 319

2.14.2

Installing

Note

Before assembly the gasket contact surfaces must be coated with soapy water so that they can be moved easily

and positioned on the flanges more accurately.

– Mask off the openings -4- below the window guide with fabric

adhesive tape.

– Dimensions of adhesive: height = approx. 10 mm, width = ap‐

prox. 40 mm.

– Slide the window run into the supports -arrows a-.
– Press the window run evenly all around against the door flange

-2-.

– Press the sealing lip of the door run from the inside against the

door flange.

– Push in the retaining clip (Pos. 3) - arrow b -.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Door internal parts

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands