manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

Note

If the airbag control indicator - K75 - indicates a fault after as‐

sembly, the event memory must be queried ⇒ Vehicle diagnostic

tester.

3.16

Removing and installing side airbag

WARNING

♦ Observe the safety instructions for pyrotechnic compo‐

nents

⇒ “3.3 Observe the general safety instructions for working

on airbag, belt tensioner and battery separation units (py‐

rotechnical components)”, page 225

 .

♦ Observe the disposal instructions for pyrotechnic compo‐

nents

⇒ “3.5 Storage, transport and disposal of airbag, belt ten‐

sioner and battery separation units (pyrotechnical com‐

ponents)”, page 226

 .

Removing
– Remove front seat

⇒ “1.1 Removing and installing front seat”, page 286

 .

– Remove front seat backrest.
– Remove backrest cover

⇒ “1.3 Removing and installing the cover and the upholstery

of the front seat backrest”, page 301

 .

– Disconnect plug connection -5- for side airbag unit -4-.
– Remove screw -3- (9 Nm).
– Unclip catch -1- for side airbag -4- from the seat rest rack -2-.
– Remove the airbag unit -4- from the seat rest rack -2-.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Airbag    

237

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Brand: Lancia Pages: 386
NavLinkz CAM-N-CV133-V Manual preview
CAM-N-CV133-V
Brand: NavLinkz Pages: 4
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Brand: GOgroove Pages: 9
Pacbrake C44059 Installation Manual preview
C44059
Brand: Pacbrake Pages: 14
Yakima K831 Manual preview
K831
Brand: Yakima Pages: 8
DEFA 412737 Fitting Instructions Manual preview
412737
Brand: DEFA Pages: 7
Prorack K869 Fitting Instructions Manual preview
K869
Brand: Prorack Pages: 15
Phonocar VM350 Mounting Instructions preview
VM350
Brand: Phonocar Pages: 2
Subaru 1998 Forester Owner'S Manual preview
1998 Forester
Brand: Subaru Pages: 298
Motoalliance Denali MA11705 Manual preview
Denali MA11705
Brand: Motoalliance Pages: 5
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Brand: Ranger design Pages: 24
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Brand: Unex Pages: 30
rockymounts SplitRailLS Installation Instructions Manual preview
SplitRailLS
Brand: rockymounts Pages: 6
Atera 080 705 User Information preview
080 705
Brand: Atera Pages: 3
Black Horse RB001BK Installation Instructions preview
RB001BK
Brand: Black Horse Pages: 5
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Brand: Lantronix Pages: 51
Jaeger 12160509J Fitting Instructions Manual preview
12160509J
Brand: Jaeger Pages: 16
Webasto H300 comfort Operating Instructions Manual preview
H300 comfort
Brand: Webasto Pages: 44

Brands by name

Popular brands

Load more brands