Skoda Rapid NH 2014 Workshop Manual Download

Page: 89 / 319

– Remove gasket -1- evenly -arrows- without bending the flange

-2-.

Installing
Press the window channel strip - 1 - by hand evenly onto the

flange - 2 -.

2.16

Removing and installing the outer win‐

dow channel strip

2.16.1

Removing

Note

♦

The core of the seal consists of a metal insert.

♦

If it is bent, the seal can no longer be straightened. It remains

“warped”.

♦

Therefore the seal must be fitted on uniformly and without

bending it.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Door internal parts

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands