Skoda Rapid NH 2014 Page 49 Workshop Manual Download

Page: 49 / 319

2.7

Tailgate seal

2.7.1

Installation instructions

♦ If the seal is re-installed, leak-tightness and tight fit can no

longer be guaranteed.

♦ For this reason, each seal which was completely removed

must be replaced with a so-called “hammer finish seal”.

♦ If the seals were detached partially, press together the sides

of the seal before installing.

2.7.2

Removing and installing tailgate seal

Removing
– Pay attention to installation instructions

⇒ “2.7.1 Installation instructions”, page 41

– Detach the seal for the tailgate -1- from the body flange.
Installing
– Press the seal -1- evenly onto the body flange.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Tailgate

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands