Skoda Rapid NH 2014 Workshop Manual Download

Page: 58 / 319

– The dash panel must be removed on the driver's side for

slackening the screw - 7 -

⇒ “1.1 Removing and installing the dash panel”, page 244

– The glove compartment must be removed on the front pas‐

senger side for slackening the screw - 7 -

⇒ “1.2 Removing and installing the glove compartment”, page

249

Setting the gap sizes
The screws -3 and 9- must be released for correctly setting the

flushness.

Note

Other measures, such as aligning the doors towards the top are ineffective. The door will drop again at the

following overpressures.

Adjusting the locking clamp

⇒ “1.3.1 Adjusting the locking clamp”, page 50

1.3.1

Adjusting the locking clamp

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

Rep. gr.57 - Front doors, door components, central locking

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands