manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

♦ Pyrotechnical components, which have fallen on a hard

surface, must not be re-installed.

♦ Before handling pyrotechnical components of the restraint

system, for example, disconnecting the electrical plug

connection, the mechanic must discharge himself electro‐

statically. The electrostatic discharge is achieved by

touching grounded metal parts, for example, by briefly

touching the door closing mechanism.

♦ Pyrotechnical components should be installed immediate‐

ly after being removed from the transport container.

♦ If work is interrupted, place the pyrotechnical components

back in the transport container.

♦ It is not permitted to leave the pyrotechnical component

unattended.

♦ Pyrotechnical components should not be treated with

grease, cleaning agents or similar products.

♦ Pyrotechnical components should not be exposed to tem‐

peratures above 100 °C, not even for short periods.

3.4

Special instructions for driver and front

passenger airbag

WARNING

♦ Driver and front passenger airbag units in an unmounted

condition are to be deposited with the impact absorber to‐

wards the top.

3.5

Storage, transport and disposal of air‐

bag, belt tensioner and battery separa‐

tion units (pyrotechnical components)

WARNING

♦ The storage is subject to the respective national legisla‐

tion.

♦ The transport is subject to national and international leg‐

islation, in which packaging, marking, labeling, and ac‐

companying documents are regulated in detail.

♦ Non-ignited pyrotechnical components must be discarded

in the original packaging in compliance with the applicable

disposal procedure according to the national legislation!

In case you have any questions, please contact your im‐

porter.

♦ Only fully ignited pyrotechnical components may be dis‐

posed of as industrial waste.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

226

     Rep. gr.69 - Passenger protection

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Metra Electronics 99-3010S Installation Instructions Manual preview
99-3010S
Brand: Metra Electronics Pages: 14
Daihatsu S85 Wiring Diagrams preview
S85
Brand: Daihatsu Pages: 41
Daihatsu S85 Workshop Manual preview
S85
Brand: Daihatsu Pages: 268
Ultra Start KE-6 Owner'S Manual preview
KE-6
Brand: Ultra Start Pages: 8
Calix M5T 187A Assembly Instructions preview
M5T 187A
Brand: Calix Pages: 5
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Brand: Brodit Pages: 2
Thule CIRCUIT 526XT Manual preview
CIRCUIT 526XT
Brand: Thule Pages: 12
FALCON RIDGE BC-3400-FC05 Instructions For Installation And Care preview
BC-3400-FC05
Brand: FALCON RIDGE Pages: 7
Volvo 2004 C70 HPT User Manual preview
2004 C70 HPT
Brand: Volvo Pages: 30
Mercedes-Benz CLS 2015 Operator'S Manual preview
CLS 2015
Brand: Mercedes-Benz Pages: 398
Xingyun XY40EV Service Manual preview
XY40EV
Brand: Xingyun Pages: 74
Edelbrock 460 Ford Installation Instructions preview
460 Ford
Brand: Edelbrock Pages: 2
Axxess AXDSPX-TY1 Installation Instructions Manual preview
AXDSPX-TY1
Brand: Axxess Pages: 16
Mitsubishi Montero 1988 Manual preview
Montero 1988
Brand: Mitsubishi Pages: 367
Mazda MX-3 1995 Workshop Manual preview
MX-3 1995
Brand: Mazda Pages: 1001
Jaeger 21260514J Fitting Instructions Manual preview
21260514J
Brand: Jaeger Pages: 11
ATS 664-0030 Installation And Operating Manual preview
664-0030
Brand: ATS Pages: 12
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Brand: Easee Pages: 21

Brands by name

Popular brands

Load more brands