manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

– Disconnect plug connection -1- and if necessary -2- (only for

vehicles with multi-function steering wheel).

– Lay aside the airbag unit in such a way that the impact ab‐

sorber points upwards.

Installing
– The installation occurs in reverse order.

WARNING

Nobody should be in the vehicle when the battery is being con‐

nected.
Pay attention to the sequence when connecting the battery ⇒ 

Electrical System; Rep. gr.  27 .

Note

If the airbag control indicator - K75 - indicates a fault after as‐

sembly, the event memory must be queried ⇒ Vehicle diagnostic

tester.

3.14

Removing and installing restoring ring

with slip ring

– Removing and installing ⇒  Electrical System; Rep. gr.  94 ;

Steering column combination switch; removing and installing

restoring ring with slip ring in the steering column combination

switch .

3.15

Removing and installing airbag unit on

the passenger side

Removing

WARNING

♦ Observe the general safety instructions for working on air‐

bag, belt tensioner and battery separation units (pyrotech‐

nical components)

⇒ “3.3 Observe the general safety instructions for working

on airbag, belt tensioner and battery separation units (py‐

rotechnical components)”, page 225

 .

♦ Observe the special instructions for driver and front pas‐

senger airbag

⇒ “3.4 Special instructions for driver and front passenger

airbag”, page 226

 .

Carry out the following tasks

WARNING

When electrostatic discharges occur, there is a risk of the air‐

bag being activated unintentionally. Therefore, the mechanic

must discharge himself electrostatically before separating the

ignition  and  earth  lead.  This  occurs,  for  example,  by  briefly

touching the body or the door closing mechanism.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Airbag    

235

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

HALE MM-03 Driver Manual preview
MM-03
Brand: HALE Pages: 44
Pivot DXB-B User Manual preview
DXB-B
Brand: Pivot Pages: 4
Alpine KCE-G7QI Installation preview
KCE-G7QI
Brand: Alpine Pages: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Brand: Whispbar Pages: 15
Chariot Carriers 51100913 Instruction Manual preview
51100913
Brand: Chariot Carriers Pages: 3
AA Products SR-A260 Instruction Manual preview
SR-A260
Brand: AA Products Pages: 4
Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Brand: Gatorback Mudflaps Pages: 4
Buick 2015 LaCrosse Getting To Know Manual preview
2015 LaCrosse
Brand: Buick Pages: 20
Oypla Leisure 4269 User Manual preview
4269
Brand: Oypla Leisure Pages: 4
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Brand: Weltmann KFZ-Teile Pages: 12
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Brand: TEINHOF Pages: 2
POOL-LINE 110050 Assembly Instructions preview
110050
Brand: POOL-LINE Pages: 2
Curt Manufacturing 58963 Installation Manual preview
58963
Brand: Curt Manufacturing Pages: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Brand: Whispbar Pages: 112
Mitsubishi 2015 OUTLANDER Owner'S Manual preview
2015 OUTLANDER
Brand: Mitsubishi Pages: 490
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Brand: Federal Signal Corporation Pages: 20
BMW X3 xDrive28i Owner'S Manual preview
X3 xDrive28i
Brand: BMW Pages: 278
Kargo Master 48132 Instruction Manual preview
48132
Brand: Kargo Master Pages: 9

Brands by name

Popular brands

Load more brands