manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

Share
Download
Skoda Rapid NH 2014 Workshop Manual Download Page 253

– Remove the steering wheel

⇒ “3.12 Summary of components of steering wheel”,

page 232

 .

– Remove steering column trim panel

⇒ “1.3 Removing and installing the steering column trim pan‐

el”, page 251

 .

– Removing dash panel insert ⇒  Electrical System; Rep. gr. 

90 .

– Remove light switch ⇒  Electrical System; Rep. gr.  96 .
– Pull plug out of the daytime running light switch and the head‐

light range control adjuster ⇒  Electrical System; Rep. gr.  96 .

– Remove cover of fuse box.
– Unscrew screws for fuse box and unhook it ⇒  Electrical Sys‐

tem; Rep. gr.  97 .

– Remove the lateral dash panel covers -1 and 2- e.g. using the

disassembly wedge -3409-.

– Remove the glove compartment

⇒ “1.2 Removing and installing the glove compartment”, page

249

 .

– Unclip frame -1-.
– Unscrew screws for radio or navigation (depending upon ve‐

hicle equipment) ⇒  Electrical System; Rep. gr.  91 .

– On vehicles without radio or navigation, remove the storage

compartment of the middle dash panel.

Air conditioning system with manual control
– Remove the heater control ⇒  Heating, Air Conditioning; Rep.

gr.  87 .

Automatic air conditioning system
– Removing the control and display unit for air conditioning sys‐

tem with control unit ⇒  Heating, Air Conditioning; Rep. gr.  87 .

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Dash panel    

245

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands