Skoda Rapid NH 2014 Workshop Manual Download

Page: 300 / 319

Installing
– The installation occurs in reverse order.

1.6

Removing and installing the grip for the

seat height adjuster

Removing

Note

To provide a better overview, the retaining clip is shown in the

illustration in its removed condition.

– Pull up the handle -1- and press the metal tab of the retaining

clip -2- towards the inside using a small screwdriver. Pull down

the handle of the adjusting lever -3-.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

292

Rep. gr.72 - Seat frames

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands