Skoda Rapid NH 2014 Workshop Manual Download

Page: 120 / 319

– The further work procedure occurs in the reverse order to the

removal.

• A functional check must be performed before installing the

door trim panel.

2.12

Removing and installing window lifter

motor

2.12.1

Removing

– Removing door trim panel

⇒ “2.2 Removing and installing the rear door trim panel ”, page

259

– Secure the door window with adhesive tape so that it does not

slide off.

– Unplug connector -4-.
– Unscrew screws -2-.
– Remove the window lifter motor with the control unit - 1 - from

the supports of the hoisting drum - 3 -.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

112

Rep. gr.58 - Rear doors, door components

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands