manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

3.4.2

Removing

Note

The trim cannot be removed without being destroyed.

Carry out the following tasks
– Remove screws -3- (1,8 Nm).
– Lever the fixing pins -2- out of the grommets -6- e.g. using a

wedge.

– The fixing pins will probably tear and remain in the grommets

-6-.

– Remove the trim -1- from the B pillar.
– Remove residues of torn pins and glue residues from the self-

adhesive strips - 4 -.

Installing
– The installation occurs in reverse order.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

186

     Rep. gr.66 - Exterior equipment

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Brand: GMC Pages: 140
Hama Pico Operating Instructions preview
Pico
Brand: Hama Pages: 2
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Brand: Safe Fleet Pages: 12
FormFit HD 10L07 Installation Instructions preview
HD 10L07
Brand: FormFit Pages: 2
Würth 071554055 User Instructions preview
071554055
Brand: Würth Pages: 36
Fab Fours H4550 Installation Instructions Manual preview
H4550
Brand: Fab Fours Pages: 13
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Brand: Rugged Ridge Pages: 3
Sagem MyCK100 User Manual preview
MyCK100
Brand: Sagem Pages: 10
Ford 2000 F 350 Owner'S Manual preview
2000 F 350
Brand: Ford Pages: 256
Menabo ANTARES KIT+1 Assembly & Instruction Manual preview
ANTARES KIT+1
Brand: Menabo Pages: 8
Seat Arona 2018 Owner'S Manual preview
Arona 2018
Brand: Seat Pages: 372
Magneti Marelli AC911 Installation Instruction preview
AC911
Brand: Magneti Marelli Pages: 3
Husky 31564 Assembly, Installation, Operation And Maintenance Instructions preview
31564
Brand: Husky Pages: 8
Quadratec 506-Rock Quick Start Quide preview
506-Rock
Brand: Quadratec Pages: 2
Honda Vezel Owner'S Manual preview
Vezel
Brand: Honda Pages: 279
Velleman CAMSET28 User Manual preview
CAMSET28
Brand: Velleman Pages: 17
Valueline SVL-CARCAM11 User Manual preview
SVL-CARCAM11
Brand: Valueline Pages: 40

Brands by name

Popular brands

Load more brands