manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

WARNING

If a thread in the support panel of the seat crossmember is

damaged during the installation, it is not permitted to rework

the damaged thread! In this case, the support panel of the seat

crossmember must be replaced.

If there is a thread damage in the support panel of the seat cross‐

member:
– Replace the affected support panel of the seat crossmember

⇒ Body Repairs; Rep. gr.  51 .

1.2

Removing and installing the seat up‐

holstery on the rail side (seat without

height adjustment)

Removing
– Remove front seat

⇒ “1.1 Removing and installing front seat”, page 286

 .

– Remove screw -1- (1 Nm).
– Lever the cap -5- out of the backrest adjustment lever -4-.
– Detach the backrest adjustment lever -4-.

Note

The backrest adjustment lever -4- cannot be detached from the adjustable axle without being destroyed.

– Open the bottom fixing latch of the seat upholstery -2- and

press the support from the wire strap.

– Loosen the seat upholstery -2- from the seat rack -1- and re‐

move the seat upholstery.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

288

     Rep. gr.72 - Seat frames

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

ZAPTEC Go Instruction Manual preview
Go
Brand: ZAPTEC Pages: 240
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Brand: Ford Pages: 12
Ironton 44596 Owner'S Manual preview
44596
Brand: Ironton Pages: 7
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Brand: Waeco Pages: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Brand: Tusk Pages: 2
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Brand: mtf TRANSPORT SYSTEM Pages: 9
Metra Electronics 99-5819 Installation Instructions Manual preview
99-5819
Brand: Metra Electronics Pages: 8
Dakota Digital CRS-3000-3 Manual preview
CRS-3000-3
Brand: Dakota Digital Pages: 20
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Brand: Havis-Shields Pages: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Brand: PEUGEOT Pages: 107
AD Boivin ZX2 2008 Adjustment Manual preview
ZX2 2008
Brand: AD Boivin Pages: 37
Honda 08P00-T7S-600 Installation Instructions preview
08P00-T7S-600
Brand: Honda Pages: 5
TATA Motors Indigo Marina Owner'S Manual & Service Book preview
Indigo Marina
Brand: TATA Motors Pages: 146
INNO TR163 Installation Instructions preview
TR163
Brand: INNO Pages: 3
Cadillac Escalade ESV Owner'S Manual preview
Escalade ESV
Brand: Cadillac Pages: 538
Prorack K443 Fitting Instructions Manual preview
K443
Brand: Prorack Pages: 14
Toyota Sienna 2000 Operating Manual preview
Sienna 2000
Brand: Toyota Pages: 277
Westfalia 300025300113 Installation Instructions Manual preview
300025300113
Brand: Westfalia Pages: 97

Brands by name

Popular brands

Load more brands