Skoda Rapid NH 2014 Workshop Manual Download

Page: 20 / 319

1.7

Bulkhead plenum chamber

1.7.1

Summary of components

1 - Bulkhead plenum chamber
Removing

– Remove the plenum

chamber cover

⇒ “1.8.2 Removing”,

page 14

– Remove engine air duct

(depending on engine).

– Remove engine control

unit and engine control

module holder.

– Remove noise insula‐

tion.

– Unscrew screws -2-.

– Remove the bulkhead

plenum chamber -1- up‐

wards and out of the ple‐

num chamber -4-.

Installing

– The installation occurs

in reverse order.

2 - Screw

❑ Tightening torque - 8

Nm.

3 - Plenum chamber
4 - Seal

Note

Ensure that the seal is correctly

seated when installing the bulkhead

plenum chamber.

5 - Damping

❑ Attached to the bulkhead plenum chamber with clamping plates.

6 - Circlip

❑ For attaching the damping on the bulkhead plenum chamber.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

Rep. gr.50 - Body - front

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands