manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

3.8

Door sill panel and wheel house trim

panel

3.8.1

Removing and installing door sill panel

Removing
– Remove the seat bench

⇒ “2.1 Removing and installing the rear seat bench”,

page 295

 .

– Remove wheel house trim panel

⇒ “3.8.2 Removing and installing wheel house trim panel”,

page 272

 .

– Remove clips -1-.
– In the rear area, unclip the clip - 4 - and the retaining clip

- 2 - of the door sill panel - 3 -.

– Loosen the door sill panel -3- from the bottom trim panel of B-

pillar.

– In the front area, unclip all the retaining clips - 2 - of the door

sill panel - 3 -.

– Remove the door sill panel - 3 - from the vehicle.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Trim panels of pillars    

271

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Jabra FREEWAY Datasheet preview
FREEWAY
Brand: Jabra Pages: 2
Jabra BT330 User Manual preview
BT330
Brand: Jabra Pages: 38
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Brand: Jeep Pages: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Brand: Jeep Pages: 6
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Vauxhall 2009 Tigra Quick Reference Manual preview
2009 Tigra
Brand: Vauxhall Pages: 2
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Brand: Blue Giant Pages: 48
TATA Motors nano genX Owner'S Manual preview
nano genX
Brand: TATA Motors Pages: 156
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Brand: Victory 4x4 Pages: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Brand: Keith Pages: 2
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Brand: Ford Pages: 38
femkes Hopper on Top User Manual preview
Hopper on Top
Brand: femkes Pages: 7
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Brand: SCC Pages: 4
Kuda 079020 Installation Instruction preview
079020
Brand: Kuda Pages: 2
Improved Racing E5G-601 Instructions Manual preview
E5G-601
Brand: Improved Racing Pages: 17

Brands by name

Popular brands

Load more brands