Skoda Rapid NH 2014 Page 303 Workshop Manual Download

Page: 303 / 319

Rear seats

2.1

Removing and installing the rear seat

bench

Removing
– Grip on both sides with both hands under the seat bench

- 1 - in the area of the mounting grommet - 2 - and pull up

forcefully and with a sudden motion in the

-direction of arrow-.

– Guide the seat bench -1- in -direction of arrow- on both sides

out of the crash hooks -2- on the left and right.

– Disconnect the plug connections for heating prior to removing

the seat bench (depending on the vehicle equipment).

– Take the seat bench -1- out of the vehicle.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Rear seats

295

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands