manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

Share
Download
Skoda Rapid NH 2014 Workshop Manual Download Page 307

74 – Seat - padding, covers

1

Covers and upholstery of the front

seats

1.1

Tools

Special tools and workshop equipment required
♦ Upholstery retaining clip pliers, e.g. - V.A.G 1634-

1.2

Removing and installing the cover and

the upholstery of the front seat cushions

Removing
– Remove front seat

⇒ “1.1 Removing and installing front seat”, page 286

 .

– Remove the front belt buckle

⇒ “1.3 Removing and installing the front seat belt buckle”, page

214

 .

– Remove the seat trim panel on the tunnel side

⇒ “1.5 Removing and installing the seat trim panel on the tun‐

nel side”, page 291

 .

– Remove the seat trim panel on the rail side:
♦ Seat without height adjustment

⇒ “1.2 Removing and installing the seat upholstery on the rail

side (seat without height adjustment)”, page 288

 .

♦ Seat with height adjustment

⇒ “1.3 Removing and installing the seat upholstery on the rail

side (seat with height adjustment)”, page 289

 .

– Unhook the clamping section -1- from the seat rack -2-.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Covers and upholstery of the front seats    

299

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands