Skoda Rapid NH 2014 Workshop Manual Download

Page: 91 / 319

Note

♦

During the removal of the seal, the sealing mass is distributed

on the inside of the seal. While doing so, the sides are slightly

bent open. If the seal is re-installed, leak-tightness and tight fit

can no longer be guaranteed.

♦

For this reason, each seal which was completely removed

must be replaced with a so-called “hammer finish seal”.

♦

If the seals were detached partially, press together the sides

of the seal before installing.

Removing
– Remove the trim panels of the pillars for removing the inside

door seal

⇒ “3 Trim panels of pillars”, page 263

– Remove sill

⇒ “3.8.1 Removing and installing door sill panel”, page 271

– Detach the inside door seal -1- from the body flange.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Door internal parts

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands