Skoda Rapid NH 2014 Workshop Manual Download

Page: 149 / 319

– Use the cutting tool BEA 000 001 to cut out the opening (di‐

ameter 18 mm).

– Use a step drill in order to drill the openings.
– First of all make the openings from the outer side of the bumper

when using a step drill. Complete the work step from the inner

side of the bumper.

– Trim the openings in a suitable manner in order to avoid dam‐

age to the paintwork.

– The glueing procedure of new sensor holders is described in

the workshop manual ⇒ Electrical System; Rep. gr. 94 .

– After installing the sensors, install the bumper

⇒ “2.1 Rear bumper”, page 135

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

4. Cutting out the openings for the parking aid sensors (drill)

141

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands