Skoda Rapid NH 2014 Workshop Manual Download

Page: 201 / 319

Letterings

5.1

Installation instructions

♦ Warm up the letterings with a hot-air blower before removing.
♦ If a lettering is removed or installed, only use the glue remover

- D 002 000 10- to remove the glue residues.

♦ If necessary, remove adhesive residues from the adhesive

tape.

♦ Make sure that the adhesive surfaces are free from dust and

grease.

♦ The letterings must be glued on immediately after cleaning.
♦ Remove protective foil from its wrapping until just before as‐

sembly.

♦ The processing temperature is about 21 ℃.
♦ The letterings cannot be removed without being damaged.

5.2

Removing and installing the emblem on the tailgate

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

5. Letterings

193

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands