Skoda Rapid NH 2014 Workshop Manual Download

Page: 171 / 319

2.1.1

Removing and installing mirror glass

WARNING

Wear protective gloves and protective goggles when working!

Removing
– Protect the edges of the housing for damage, e.g. cover with

textile adhesive tape.

– Swivel the mirror glass - 1 - in the maximum position.
– Press off the mirror glass -1- from the holder -2- and the hous‐

ing -arrow a- for example using a wide plastic wedge.

Installing
– Press the mirror glass in the centre onto the holder in the

housing.

The mirror glass clicks audibly into place.
• Subsequently perform a functional test.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Exterior mirrors

163

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands