Skoda Rapid NH 2014 Workshop Manual Download

Page: 160 / 319

1 - Body sheet profiles
2 - Fixing bolts
3 - Seal

❑ Is part of the window.

4 - Side window

1.11

Removing and installing side window

(Spacebook)

WARNING

It is essential to wear protective goggles and gloves when cut‐

ting hardened PUR adhesive sealing material and when han‐

dling the cutting cord.

Removing undamaged side window
– Protect vehicle interior from glass splinters.
– Remove top trim panel of pillar C and D

⇒ “3.7 Removing and installing C and D pillar trim panels

(Spaceback)”, page 270

– Remove glass pieces up to the glue sealing material.
– Cover the painted surfaces along the window with textile ad‐

hesive tape.

– Remove antenna plug (depending upon equipment).

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

152

Rep. gr.64 - Glazing

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands