Skoda Rapid NH 2014 Workshop Manual Download | Manualshive

Page: 235 / 319

background image

3.6

Replacing parts of the airbag system

Accident with deployment of airbag

Note

“Compulsory registration before repair” Note regarding deploy‐

ment of airbag and non-deployment of airbag in the ⇒ Technical

Service Handbook .

Elsa ⇒
Technical Service Handbook
Technical product information ⇒
Body/equipment ⇒
Operation ⇒
Occupant protection ⇒
Airbag fire accident (safety relevant inquiry-registration docu‐

ments) ⇒
Systems
The following parts must, in principle, be replaced by new original

parts only:
♦ Central control unit for airbag system, VW 10

1)

.

♦ Airbag unit on the driver's side

2)

.

♦ Airbag unit on the front passenger's side

2)

.

♦ Side airbag unit on the driver's side

2)

.

♦ Side airbag unit on the front passenger's side

2)

.

♦ Seat covering

3)

.

♦ Head airbag driver's side

2)

.

♦ Head airbag front passenger's side

2)

.

♦ Top trim panel of A pillar

4)

.

♦ Top trim panel of B pillar

4)

.

♦ Top trim panel of C pillar

4)

.

♦ Headlining

4)

.

♦ Restoring ring with slip ring

5)

.

♦ Driver seat belt tensioner with seat belt

2)

.

♦ Front passenger seat belt tensioner with seat belt

2)

.

♦ Seat belt tensioners with seat belts for the rear seats

2)

.

1)

If the front and side airbag unit or head airbag unit and seat belt

tensioner have ignited, the control unit may be used again - up to

three times.

2)

In the event of ignition.

3)

In the event of ignition of the side airbag unit.

4)

In the event of ignition of the head airbag unit.

5)

In the event of ignition of the driver airbag unit.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Airbag

227

«
...
233
234
235
236
237
...
»

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Brand: Warrior Products Pages: 2

Brand: Toyota Pages: 56

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Vantage 12 Series

Brand: Ecco Pages: 5

Brand: Kuda Pages: 3

Brand: RAM Pages: 496

Brand: U.S. General Pages: 8

Brand: Fab Fours Pages: 13

Brand: RAM Pages: 13

Brand: Bestop Pages: 31

RVS systems RVS-M641

Brand: Safe Fleet Pages: 24

Brand: BrandMotion Pages: 6

Brand: iDataLink Pages: 6

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brand: Bestop Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands