manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

Adjusting the adjusting buffer

Note

♦

Install the adjusting buffer - 2 and 3 - on the left and right up to the stop.

♦

Turn the adjusting buffers by 90° if required, in order to pretension the flap.

– After the front flap has been adjusted, the locking clamp - 1 -

can once again be installed and adjusted

⇒ “1.10.2 Adjusting the locking clamp”, page 34

 .

– The front flap can be adjusted in the front area to the height of

the wings with the flap lock -5-

⇒ “1.10.1 Adjusting the flap lock”, page 33

 .

– After the flap has been adjusted, the locking clamp has been

installed and all the connections have been tightened, the ad‐

justing buffers can be turned if required.

– After carrying out adjustment work, perform corrosion protec‐

tion measures on the hinges -6- and the screws -7- .

1.10.1

Adjusting the flap lock

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Front flap    

33

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Hama Pico Operating Instructions preview
Pico
Brand: Hama Pages: 2
Camcar 40104 Mounting Instructions preview
40104
Brand: Camcar Pages: 6
DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Brand: DANA Pages: 42
dallara F305 Manual preview
F305
Brand: dallara Pages: 37
Yakima BOA Installation Instructions Manual preview
BOA
Brand: Yakima Pages: 8
Kargo Master 40131 Installation Manual preview
40131
Brand: Kargo Master Pages: 5
Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Brand: Taffio Pages: 8
Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
Yakima RoadShower 10G Quick Start Manual preview
RoadShower 10G
Brand: Yakima Pages: 12
Globalsat MR-350P Installation Manual preview
MR-350P
Brand: Globalsat Pages: 2
femkes Hopper on Top User Manual preview
Hopper on Top
Brand: femkes Pages: 7
Flash Cover MN019 Instructions preview
MN019
Brand: Flash Cover Pages: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Brand: Porsche Pages: 98
Saab 9000 1985 Service Manual preview
9000 1985
Brand: Saab Pages: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Brand: A-rival Pages: 23
r.LiNK RL2-NBT Manual preview
RL2-NBT
Brand: r.LiNK Pages: 20
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Brand: Lexus Pages: 830
Westin 28-21030 Instructions preview
28-21030
Brand: Westin Pages: 3

Brands by name

Popular brands

Load more brands