Skoda Rapid NH 2014 Workshop Manual Download

Page: 40 / 319

1.10

Adjusting the bonnet

Note

♦

The vehicle must be positioned on the flat ground in order to adjust the bonnet.

♦

The adjusting buffers -2- on the left and right are not used for the adjustment. They have the function to

stabilise or dampen the bonnet.

♦

The bonnet is correctly adjusted if in the closed state it has an overall even gap size, is not positioned too

far outwards or inwards and the contours are aligned.

♦

The bonnet must latch in the flap lock without using increased force.

♦

The nuts are not unscrewed, only slackened.

– Remove locking clamp -1-

⇒ “1.8 Removing and installing the locking clamp”, page 29

– The mean of the front flap can be taken between the wings by

slackening the nuts -6- on the left and right hinges -7-.

– Ensure parallelism of gap dimensions ⇒ Body Repairs; Rep.

gr. 00 ; Technical data; body gaps; front body .

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

Rep. gr.55 - Bonnet, rear lid

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands