manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

Share
Download
Skoda Rapid NH 2014 Workshop Manual Download Page 37

Note

♦

When installing the Bowden cable - 3 -, ensure that the grommet - 5 - is correctly secured.

♦

When attaching the Bowden cable - 3 -, pay attention to the mandatory clipping - 4 -.

• Before closing the front flap, carry out a functional test of the

operating lever and the Bowden cable.

1.8

Removing and installing the locking clamp

Removing
– Unscrew screws -3-.
– Remove the locking clamp - 1 - from the front flap - 2 -.
Installing
– Tightening torque of screws -3- (10 Nm).
– Adjust the locking clamp to the flap lock

⇒ “1.10.2 Adjusting the locking clamp”, page 34

 .

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Front flap    

29

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands