Skoda Rapid NH 2014 Page 131 Workshop Manual Download

Page: 131 / 319

2.20

Removing and installing the outer win‐

dow channel strip

2.20.1

Removing and installing

Note

♦

The core of the seal consists of a metal insert. If it is bent, the

seal can no longer be straightened. It remains “warped”.

♦

Therefore the seal must be removed uniformly and without

bending it.

Removing
– Detach window channel strip - 1 - evenly - arrows - from the

flange - 2 -.

Installing
– Press the window channel strip - 1 - by hand evenly onto the

flange - 2 -.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Door internal parts

123

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands