background image

 

Advanced Million Color ATV Lighting Kit 

Part Number: LU-MC-ADV-M_X 

 

Warning:

 Please check your state and local laws before installing this ATV Lighting Kit. Every state has different policies and 

procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may 
receive while using this lighting kit. 

This kit is for off road use only.

 

 
Warning:

 The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this 

kit will void all warranties.  
 

The control box that is used to power this ATV lighting Kit must be installed in a dry location! Having this part exposed to 
water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will VOID all 
warranties. 
 

It is recommended to install each ATV lighting strip using 3M™ Adhesion Promoter which allows for a much stronger bond 
between the adhesive tape of the light strip and the cleaned mounting surface of your ATV. This is an optional installation 
accessory that is NOT included with your ATV lighting kit. 
 

PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED ATV KIT. 
 
ATV Lighting Kit Includes: 

 

ATV LED Lighting Strips 

 

(1) Control Box 

 

 

Wireless Remote (Quantity Depends on Kit Ordered) 

 

Zip Ties 

 

ATV Kit Installation: 

1.

 

Before installing your ATV lighting kit, be sure to power and test it for full functionality. Connect the red power wire 
to the positive terminal of the battery and the black ground wire to the negative terminal of the battery. Once the kit 
is powered, use the included remote to ensure it is functioning properly. If it is working correctly, turn the kit off and 
disconnect the power and ground wires from the battery to prepare for installation. 
 

2.

 

Optional

: Remove any trim pieces from your ATV that may hinder the installation of the lighting strips.  

 

3.

 

Begin by first laying out the LED lighting strips similar to the way they will be installed. Make sure that the wires will 
be able to be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires and 
strips away from all moving parts that may come in contact with any part of the kit.  

Note: IF A POWER WIRE IS PINCHED, IT WILL CAUSE THE KIT TO MALFUNCTION AND WILL VOID THE WARRANTY 
DUE TO PHYSICAL DAMAGE. 

 

4.

 

Temporarily place the ATV lighting strips to their intended mounting locations and route the power wires to the 
planned control box mounting area. Use the supplied zip ties to secure the power wires to their mounting points. 

Be 

sure to keep the power wires away from the suspension, any direct heat sources and/or moving parts. 

A few 

recommended locations on your ATV to mount the light strips are under the front and rear fenders, hood, side panels, 
and radiator scoops. 
 

5.

 

Once the ATV lighting strips and wires have been mocked up, clean the proposed mounting surfaces with an alcohol 
prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest bonding 
results from the doubled sided adhesive tape.  

Note: 

The surface area must be free of all oils, moisture, dirt, and wax in order for the supplied adhesive tape to bond 

and adhere to the installation surface correctly.  

Optional: 

To achieve the strongest bond between the lighting strips and your ATV, you can purchase and apply 3M 

Adhesive Promoter, prior to mounting each strip. 
 

Summary of Contents for Advanced Million Color

Page 1: ...se the included remote to ensure it is functioning properly If it is working correctly turn the kit off and disconnect the power and ground wires from the battery to prepare for installation 2 Optional Remove any trim pieces from your ATV that may hinder the installation of the lighting strips 3 Begin by first laying out the LED lighting strips similar to the way they will be installed Make sure t...

Page 2: ... instructional videos that can be found at www YouTube com LEDGlow Wireless Remote Functions This kit provides multiple lighting patterns and several brightness levels which are easily operated using the included wireless remote The remote includes four buttons A B C D Button A Cycles through 15 solid colors as well as a color cycle and a color fade pattern Hold for 5 seconds to select brightness ...

Page 3: ...OLLOWING THE REPAIR OR REPLACEMENT OF THAT PART OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY WHICHEVER IS GREATER 2 EXCLUSIVE REMEDY ACCEPTANCE PURCHASER S EXCLUSIVE REMEDY AND LEDGLOW S SOLE OBLIGATION IS TO SUPPLY OR PAY FOR ALL LABOR NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS LEDGLOW WILL REFU...

Page 4: ...state to state or from country to country Some states or countries do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you You are advised to consult applicable state or country laws for a full determination of rights ...

Reviews: