Simrad GO XSE Series Operator'S Manual Download Page 190 | Manualshive

Page: 190 / 242

background image

Select time and animation speed from the menu.

SiriusXM weather

About SiriusXM weather

Ú

Note:

SiriusXM weather is available for North America only.

When a supported Navico satellite weather receiver module is
connected to your system and with the appropriate subscription,
SiriusXM marine weather information is available.
The options available depend on the satellite weather receiver
module connected to your system and your subscription.
SiriusXM weather service covers a variety of North American inland
waters and coastal areas. For more information refer to
www.siriusxm.com/sxmmarine.

Sirius status panel

When the weather module is connected to the system, you get
access to the Sirius status panel.

The status panel shows signal strength is indicated as 1/3 (weak),
2/3 (good) or 3/3 (preferred). It also includes antenna status, service
level, and the electronic serial number for the weather module.

Sirius weather panel

Sirius weather can be displayed as an overlay on your chart panel.

190

Weather

| GO XSE/XSR Operator Manual

«
...
188
189
190
191
192
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: GE Pages: 14

Brand: GE Pages: 11

Brand: GE Pages: 20

Druck ADTS 2 Series

Brand: GE Pages: 18

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: FJC Pages: 2

Brand: Malmet Pages: 14

Brand: Zempire Pages: 2

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: IDEAL Pages: 12

Brand: Olympus Pages: 56

Brand: TATU Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands