manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Starting from blank

Select to create your own dashboard from scratch.
Use menu options to name the dashboard and manage gauges on
the dashboard.

Copying an existing layout

Select to copy an existing layout that you have made.
Use menu options to name the dashboard and manage gauges on
the dashboard.

Using a built-in template

Select a pre-defined template to create a dashboard. The template
dashboards reflect your vessel configuration.
Use menu options to name the dashboard and manage gauges on
the dashboard.

Customizing the dashboard

You can use edit menu options to:

•

change the data for each of the gauges in any dashboard

•

set limits for analog gauges

•

change the dashboard layout

Ú

Note: 

You cannot change the layout of pre-defined dashboards

or dashboards you have created using built-in templates.

Adding gauges

Select a gauge in the menu and then position it on the dashboard.

180

Instruments

 | GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Panasonic AJSPD850P - P2 DECK Operating Instructions Manual preview
AJSPD850P - P2 DECK
Brand: Panasonic Pages: 73
A.MENARINI GlucoMen Areo Quick Manual preview
GlucoMen Areo
Brand: A.MENARINI Pages: 2
ParaBody 808 User Manual preview
808
Brand: ParaBody Pages: 6
Sailmon E4 Installation Manual preview
E4
Brand: Sailmon Pages: 10
B&W Tek Sol Series User Manual preview
Sol Series
Brand: B&W Tek Pages: 12
B&G V90 Operating Manual preview
V90
Brand: B&G Pages: 129
b&o Beocord 1200 Operating Instructions Manual preview
Beocord 1200
Brand: b&o Pages: 46
vanEE AI Series User'S And Installer'S Manual preview
AI Series
Brand: vanEE Pages: 52
Caddon Hives WBC Assembly Instructions preview
WBC
Brand: Caddon Hives Pages: 3
Warehouse-lighting LTR Series Installation Instructions preview
LTR Series
Brand: Warehouse-lighting Pages: 3
Eagle Group SHT Series Operation Manual preview
SHT Series
Brand: Eagle Group Pages: 8
E2S A112N Installation Instructions preview
A112N
Brand: E2S Pages: 5
Gaspardo PA2 Use And Maintenance preview
PA2
Brand: Gaspardo Pages: 196
RAB X34 Installation preview
X34
Brand: RAB Pages: 2
Parkside PFMR 1400 A1 Original Operating Instructions preview
PFMR 1400 A1
Brand: Parkside Pages: 58
Yanmar RT66 Operator'S Manual preview
RT66
Brand: Yanmar Pages: 49
Fagor MX1000 Operating Instruction preview
MX1000
Brand: Fagor Pages: 12
Baltic POSEIDON User Manual preview
POSEIDON
Brand: Baltic Pages: 68

Brands by name

Popular brands

Load more brands