Simrad GO XSE Series Operator'S Manual Download Page 46 | Manualshive

Page: 46 / 242

background image

Navionics charts

Some Navionics features require the most current data from
Navionics. For those features, a message is displayed stating that the
feature is unavailable if you do not have the appropriate Navionics
charts or chart card inserted. For more information on what is
required for these features, refer to www.navionics.com.
You can also get a message if you try to use a restricted feature
when the Navionics chart card is not activated. To activate the card,
contact Navionics.

Navionics specific chart options

Photo overlay

Photo overlay enables you to view satellite photo images of an area
as an overlay on the chart. The availability of such photos is limited
to certain regions, and cartography versions.
You can view photo overlays in either 2D or 3D modes.

No Photo overlay

Photo overlay, land only

Full Photo overlay

Photo transparency

The Photo transparency sets the opaqueness of the photo overlay.
With minimum transparency settings the chart details are almost
hidden by the photo.

Minimum transparency

Maximum transparency

46

Charts

| GO XSE/XSR Operator Manual

«
...
44
45
46
47
48
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Canta Pages: 2

Brand: NAD Pages: 10

Brand: Tascam Pages: 128

Brand: ParaBody Pages: 6

Brand: ZIGBEE Pages: 6

Brand: Daisy Pages: 2

Below Ground Pool Cover Box

Brand: Daisy Pages: 3

Brand: NANLUX Pages: 39

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Growers Supply 109722

Brand: FarmTek Pages: 9

Brand: Raven Pages: 48

Brand: Pacific Pages: 16

Brand: Nakayama Pages: 14

Brand: Yuwell Pages: 2

Brand: Masalta Pages: 13

Brand: GREAT PLAINS Pages: 190

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands