Simrad GO XSE Series Operator'S Manual Download Page 22 | Manualshive

Page: 22 / 242

background image

Menu button

Displays the menu of the active panel. Use menu options to
customize the image. The panel menu options are further explained
later in this manual in each application chapter.

Instrument bar

The instrument bar displays information from sensors connected to
the system.
By default, the instrument bar is shown on the panel. You can turn
the instrument bar off.
You can select the predefined bar to be shown and you can change
the information displayed in the predefined bar. Refer to

the instrument bar"

Control bar

The control bar contains buttons for launching controllers or
features enabled in your system. The different controllers are
described in applicable chapters later in the manual.

22

Introduction

| GO XSE/XSR Operator Manual

«
...
20
21
22
23
24
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: A.MENARINI Pages: 2

Brand: made for movement Pages: 51

Brand: Jet Pages: 12

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 86

Brand: Native Instruments Pages: 245

Brand: Yamaha Pages: 29

Brand: Xtricity Pages: 4

Brand: Focal Meditech Pages: 10

Brand: Rohm Pages: 17

Brand: B & G Pages: 92

Signature IVAC 710 Series

Brand: Alaris Medical Systems Pages: 140

AX2090-ND80 Series

Brand: Beckhoff Pages: 41

Brand: Delta Light Pages: 2

Brand: Nordson EFD Pages: 103

Brand: 6K Products Pages: 17

IPURE PE25K120V

Brand: Intermatic Pages: 26

Brand: Martek Pages: 39

Spacelabs Medical 90239A

Brand: OSI Systems Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands