Simrad GO XSE Series Operator'S Manual Download Page 63 | Manualshive

Page: 63 / 242

background image

Navigating

About navigating

The navigation function included in the system allows you to
navigate to the cursor position, to a waypoint, or along a predefined
route.
If autopilot functionality is included in your system, the autopilot
can be set to automatically navigate the vessel.
For information about positioning waypoints and creating routes,
refer to

"Waypoints, routes, and tracks"

Navigation panels

The Nav panel

The Nav panel is activated from the Home page, either as a full page
panel or as part of a split page.

A Data fields
B Vessel heading

C

Bearing to next routepoint

D Route information

Indicates the distance of the route, the route name, and the
estimated time to reach the end of the route.

6

Navigating

| GO XSE/XSR Operator Manual

63

«
...
61
62
63
64
65
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

Brand: Garelick Pages: 2

Brand: Garelick Pages: 2

Brand: Gardigo Pages: 32

Brand: Olympus Pages: 56

DeviceNet CompactPCI 1784-CPCIDS

Brand: Allen-Bradley Pages: 36

Brand: Exmark Pages: 36

Brand: Manley Pages: 18

Brand: Carbatec Pages: 29

Brand: PurAthletics Pages: 2

Brand: Hella Gutmann Pages: 48

Brand: XD COLLECTION Pages: 28

Brand: Avid Technology Pages: 39

electronic music instrument

Brand: Quintet Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands