Simrad GO XSE Series Operator'S Manual Download Page 231 | Manualshive

Page: 231 / 242

background image

•

Un-select the devices that are to be removed from the control
bar.

•

Select None to remove all CZone devices from the control bar.

Multiple switching devices can be connected to the network. When
you select to display more than the maximum of devices allowed at
a time, a message informs you the maximum has been reached.

CZone digital switching control bar

If configured and setup properly, the CZone digital switching device
can be operated from the control bar.

Control bar buttons

The button indicates the status of the switch.

Off (black)
The switch is OFF.
On (blue)
The switch is ON.
Error (red)
There is a switch or communication error.

Integration of 3 party devices

| GO XSE/XSR Operator Manual

231

«
...
229
230
231
232
233
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: B&K Pages: 5

Brand: B&K Pages: 28

Brand: York Fitness Pages: 34

Brand: Quincy lab Pages: 4

Brand: GALBIATI Pages: 20

Brand: XanLite Pages: 4

Brand: York Pages: 16

i.Profiler plus

Brand: Zeiss Pages: 66

Brand: Accurate Technology Pages: 10

Brand: Gage Bilt Pages: 28

Brand: Masterclock Pages: 19

Carestation 620

Brand: GE Pages: 268

Brand: GE Pages: 50

Brand: Kelso Pages: 21

Brand: BH FITNESS Pages: 24

Brand: Best Fitness Pages: 26

Water Inlet Suction Hose

Brand: Nilfisk-Advance Pages: 8

Brand: TRX Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands