Simrad GO XSE Series Operator'S Manual Download Page 211

Page: 211 / 242

Missing notifications

By default, the connection profile for the phone is set to

auto

The connection profile should be changed to

alternative

if one of

the following issues occurs:

•

the phone is connected and the alert type is set to pop-up or
notification, but there is either no alert or the alert is very delayed

•

the phone is connected and there is no sound on the phone
when talking

See details for how to display the device details in

"Managing Bluetooth

devices"

on page 211.

To change the alert setting for the phone notifications, see

"Message

settings"

on page 210.

Text messages appearing on the iPhone, but not on the

MFD

Check that the text app is not open and active on the iPhone.

Managing Bluetooth devices

Bluetooth enabled devices within range are shown in the Bluetooth
devices dialog. Refer to

"Bluetooth options"

on page 202.

Using your phone with the MFD

| GO XSE/XSR Operator Manual

211

Summary of Contents for GO XSE Series



















































































































































































































































Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands

Simrad GO XSE Series, Operator'S Manual

Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands