manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Displaying information about chart items

When you select a chart item, a waypoint, a route, or a target, basic
information for the selected item is displayed. Select the chart item's
pop-up to display all available information for that item. You can
also activate the detailed information dialog from the menu.

Ú

Note: 

If you are viewing applicable C-MAP charts on your

system, you can select marine objects to display information
about services and available multimedia (photos) associated
with the location or object.

Ú

Note: 

Pop-up information has to be enabled in chart settings to

see basic item information.

Using the cursor on the panel

By default, the cursor is not shown on the panel.
When you activate the cursor, the cursor position window is
displayed. When the cursor is active, the panel does not pan or
rotate to follow the vessel.

Go to cursor

You can navigate to a selected position on the image by positioning
the cursor on the panel, and then using the go to cursor menu
option.

Charts

 | GO XSE/XSR Operator Manual

37

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Makerfire N10 Instructions Manual preview
N10
Brand: Makerfire Pages: 10
ZOLL R Series In-Service Manual preview
R Series
Brand: ZOLL Pages: 5
Accu-Chek Compact Pocket User Manual preview
Compact
Brand: Accu-Chek Pages: 3
iBin Compact Installation Instructions preview
Compact
Brand: iBin Pages: 2
Keiser M3 Calibration Procedure preview
M3
Brand: Keiser Pages: 2
ECA OASIS Installation Sheet preview
OASIS
Brand: ECA Pages: 3
Nautilus ONE Owners Instructions And Assembly preview
ONE
Brand: Nautilus Pages: 12
Wavetek 452 Instruction Manual preview
452
Brand: Wavetek Pages: 74
Fairchild 670 Instruction Manual preview
670
Brand: Fairchild Pages: 16
BACtrack S75 Owner'S Manual preview
S75
Brand: BACtrack Pages: 13
TA Instruments DHR Series Getting Started Manual preview
DHR Series
Brand: TA Instruments Pages: 35
Olsen Infinity Operation Manual preview
Infinity
Brand: Olsen Pages: 56
Waterous K Series Operation And Maintenance Instruction preview
K Series
Brand: Waterous Pages: 5
3TECH TS-12 Manual preview
TS-12
Brand: 3TECH Pages: 32
4EVAC Compact 500 Operation Manual preview
Compact 500
Brand: 4EVAC Pages: 15
Facsimile Genius Use And Maintenance Manual preview
Genius
Brand: Facsimile Pages: 16
Calix 804Mesh Quick Start Manual preview
804Mesh
Brand: Calix Pages: 9
Califone WT1 User Manual preview
WT1
Brand: Califone Pages: 7

Brands by name

Popular brands

Load more brands