manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

For source setup information, refer to the unit's Installation Manual.

Range

The range setting determines the distance out to the left and right
of the center.

Preset range levels

Select a preset range level manually from the menu.

Auto range

In auto range, the system automatically displays the whole range
from the water surface to the bottom.
Auto is the preferred setting for fish finding.
Select the range option and then the auto option in the menu.

Frequencies

Two frequencies are supported. 800 kHz provides the sharpest
image without sacrificing range. While 455 kHz can be used in
deeper waters, or for expanded range capabilities.

Contrast

Determines the brightness ratio between light and dark areas of the
screen.

Ú

Note: 

We recommend that you use the auto contrast option.

Palettes

Used for selecting the image's color palette.

View

Specifies if the SideScan page displays the left side of the image
only, right side only, or left and right side at the same time.

SideScan

 | GO XSE/XSR Operator Manual

161

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Walker Bay 8 Assembly Instructions Manual preview
8
Brand: Walker Bay Pages: 8
Ohmeda Giraffe OmniBed Operator'S Manual preview
Giraffe OmniBed
Brand: Ohmeda Pages: 54
Nakayama PS5000 Manual preview
PS5000
Brand: Nakayama Pages: 37
Parker SC80 Operator'S Manual preview
SC80
Brand: Parker Pages: 39
Nederman RBU 1300 User Manual preview
RBU 1300
Brand: Nederman Pages: 255
Omlet Eglu Cube Instructions preview
Eglu Cube
Brand: Omlet Pages: 2
Omicron CPC 100 Reference Manual preview
CPC 100
Brand: Omicron Pages: 382
Omicron CP TD1 Reference Manual preview
CP TD1
Brand: Omicron Pages: 188
SandenVendo HFD000006 Technical & Service Manual preview
HFD000006
Brand: SandenVendo Pages: 19
SANDIA aerospace STX 165 Pilot'S Manual preview
STX 165
Brand: SANDIA aerospace Pages: 10
Zimmer OptonPro Operating Instructions Manual preview
OptonPro
Brand: Zimmer Pages: 54
Zimmer Cryo 6 Manual preview
Cryo 6
Brand: Zimmer Pages: 4
Zimmer Biomet Tricera Instruction Manual preview
Tricera
Brand: Zimmer Biomet Pages: 23
Zimmer XYR Series Installation And Operating Instructions Manual preview
XYR Series
Brand: Zimmer Pages: 16
Zimmer XYR Series Installation And Operating Instructions preview
XYR Series
Brand: Zimmer Pages: 2
Zimmer CryoMini Operating Instructions Manual preview
CryoMini
Brand: Zimmer Pages: 32
Zimmer Soleo SonoStim Instructions For Use Manual preview
Soleo SonoStim
Brand: Zimmer Pages: 96
Kärcher R 100 Manual preview
R 100
Brand: Kärcher Pages: 20

Brands by name

Popular brands

Load more brands