manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

The autopilot will engage in the selected mode, and the autopilot
controller will change to show active mode options.
To disengage the autopilot:

•

Select the standby button

When the autopilot is in standby, the boat must be steered
manually.

Autopilot indication

The status bar shows autopilot information as long as an autopilot
computer is connected.

Autopilot modes 

The autopilot has several steering modes. The number of modes
and features within the mode depend on the autopilot computer,
the boat type and available inputs.

Non-Follow Up mode (NFU)

In this mode the port and starboard buttons are used to control the
rudder.
Activate this mode by selecting the port or starboard button when
the autopilot is in standby.

Follow-Up mode (FU)

In this mode the rudder moves to a set rudder angle. The rudder
position is maintained at the set angle.

76

Autopilot

 | GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

zipwake E Series Operator'S Quick Manual preview
E Series
Brand: zipwake Pages: 2
zipwake E Series Start-Up Checklist preview
E Series
Brand: zipwake Pages: 2
NARGESA H1 Instruction Book preview
H1
Brand: NARGESA Pages: 33
JB-Lighting P4 Operating Instructions Manual preview
P4
Brand: JB-Lighting Pages: 60
Keiser M SERIES Manual preview
M SERIES
Brand: Keiser Pages: 82
Keiser M SERIES Calibration Instruction preview
M SERIES
Brand: Keiser Pages: 4
Rainbow Quantum Instruction Manual preview
Quantum
Brand: Rainbow Pages: 18
Patlite LS7 Instruction Manual preview
LS7
Brand: Patlite Pages: 28
Darco Web Ankle Brace Quick Manual preview
Web Ankle Brace
Brand: Darco Pages: 2
Darkly Labs Emblaser 2 Installing preview
Emblaser 2
Brand: Darkly Labs Pages: 13
DARAY SL180 Operating & Installation Manual preview
SL180
Brand: DARAY Pages: 24
Darco Body Armor Night Splint Instructions preview
Body Armor Night Splint
Brand: Darco Pages: 2
LaboGene Mars Service Manual preview
Mars
Brand: LaboGene Pages: 59
Raymarine ST70 Instrument Quick Reference Manual preview
ST70 Instrument
Brand: Raymarine Pages: 12
Raven SmarTrax Operation Manual preview
SmarTrax
Brand: Raven Pages: 73
Tascam DA-40 Tehnical Documentation preview
DA-40
Brand: Tascam Pages: 3
RAB Lighting SR2 Installation Instructions preview
SR2
Brand: RAB Lighting Pages: 4
campgo Raiju User Manual preview
Raiju
Brand: campgo Pages: 33

Brands by name

Popular brands

Load more brands