manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Turn variables

All turn patters have settings that you can adjust before you start a
turn, or at any time when the boat is in a turn.

U-turn

Changes the current set heading by 180°.
Turn variable:

•

Turn radius

C-turn

Steers the vessel in a circle.
Turn variable:

•

Turn radius

•

Degrees to turn

Spiral

Makes the vessel turn in a spiral with a decreasing or increasing
radius.
Turn variables:

•

Initial radius

•

Radius change per loop

•

Number of loops

Zigzag-turn

Steers the vessel in a zigzag pattern.

Trolling motor autopilot

 | GO XSE/XSR Operator Manual

93

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

ABB ACS880-01 Series Installation Manual preview
ACS880-01 Series
Brand: ABB Pages: 238
JB Systems INFERNO Operation Manual preview
INFERNO
Brand: JB Systems Pages: 12
Bahco BH6 Service Manual preview
BH6
Brand: Bahco Pages: 9
Velocitek SC-1 Reference Manual preview
SC-1
Brand: Velocitek Pages: 81
ABS ABS-Lock X-Flat Instruction Manual preview
ABS-Lock X-Flat
Brand: ABS Pages: 8
ABS ABS-Lock X-DURCH Instruction Manual preview
ABS-Lock X-DURCH
Brand: ABS Pages: 8
ABS ABS-Lock DH05 Installation Manual preview
ABS-Lock DH05
Brand: ABS Pages: 8
Gardena 13137-20 Quick Start Manual preview
13137-20
Brand: Gardena Pages: 8
GARANT SG1 Operation Manual preview
SG1
Brand: GARANT Pages: 239
p-light Midi Installation And Instructions For Use preview
Midi
Brand: p-light Pages: 36
Velp Scientifica ECO 8 Operation Manual preview
ECO 8
Brand: Velp Scientifica Pages: 12
Yamaha D24 Upgrade Manual preview
D24
Brand: Yamaha Pages: 24
J&M Nitro Gro 5010 Assembly Manual preview
Nitro Gro 5010
Brand: J&M Pages: 33
Abbott i-STAT Alinity Quick Reference Manual preview
i-STAT Alinity
Brand: Abbott Pages: 64
Gako A052 Instruction Book preview
A052
Brand: Gako Pages: 22
ABB FEN-21 User Manual preview
FEN-21
Brand: ABB Pages: 38
ABS Dome OnTop Weight Manual preview
Dome OnTop Weight
Brand: ABS Pages: 8
A.J.Antunes MPS-250 Manual preview
MPS-250
Brand: A.J.Antunes Pages: 24

Brands by name

Popular brands

Load more brands