manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Responding to an incoming call

A call must be answered or rejected from the phone.
You can respond to an incoming call by a text message (not
available for iPhones).

Message settings

You can define message templates and set how you want the alert
to appear in the settings dialog.

Phone troubleshooting

Not possible to connect an iPhone

The first time an MFD attempts to connect to an iPhone, the
following errors might appear:

•

connection failing, giving a message saying that the phone is not
available for connection

•

the phone does not list the correct name for the MFD

If this happens, try the following:

•

reboot the MFD and restart the phone

•

check that the phone is not connected to any other Bluetooth
devices

•

manually set the iPhone to allow notifications from the MFD:

210

Using your phone with the MFD

 | GO XSE/XSR Operator

Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

MacDon 912 Operator'S Manual preview
912
Brand: MacDon Pages: 84
MacDon 625 Operator'S Manual preview
625
Brand: MacDon Pages: 89
Patton electronics 2012 Installation And Operation Manual preview
2012
Brand: Patton electronics Pages: 18
NAUTICAST B2 Product Manual preview
B2
Brand: NAUTICAST Pages: 26
YATEK ECO Owner'S Manual preview
ECO
Brand: YATEK Pages: 72
JB Systems INFERNO Operation Manual preview
INFERNO
Brand: JB Systems Pages: 12
AcceleDent aura Frequently Asked Questions preview
aura
Brand: AcceleDent Pages: 3
Zero 88 Solution Quick Start Manual preview
Solution
Brand: Zero 88 Pages: 32
Nakayama WB2000 Manual preview
WB2000
Brand: Nakayama Pages: 14
L-Acoustics LA4X Technical Bulletin preview
LA4X
Brand: L-Acoustics Pages: 5
Yamaha MagicStomp Effect List preview
MagicStomp
Brand: Yamaha Pages: 31
Waves SUB Align User Manual preview
SUB Align
Brand: Waves Pages: 8
Teac BB-1000CD Release Notes preview
BB-1000CD
Brand: Teac Pages: 2
Kamar LW0034 User Manual preview
LW0034
Brand: Kamar Pages: 2
Pfeuffer 1520 9001 Operating Instructions Manual preview
1520 9001
Brand: Pfeuffer Pages: 32
WATSON INDUSTRIES AHRS-E304 Owner'S Manual preview
AHRS-E304
Brand: WATSON INDUSTRIES Pages: 17
Fri-Jado STG 5-I Instructions Manual preview
STG 5-I
Brand: Fri-Jado Pages: 48
Janschitz Milky 13360 Operating Instruction preview
Milky 13360
Brand: Janschitz Pages: 40

Brands by name

Popular brands

Load more brands