Simrad GO XSE Series Operator'S Manual Download Page 163 | Manualshive

Page: 163 / 242

background image

DownScan

About DownScan

DownScan provides detailed images of structure and fish directly
below your boat. The DownScan panel is available when a
DownScan capable transducer is connected to the system.

The DownScan panel

A

Surface

B

Fish arch. The fish arches come from the FishReveal feature.
The FishReveal feature is enabled by default, but if it is
turned off then the fish arches are not shown on the
DownScan image.

C

Under water brush pile

D

Bottom

E

Depth scale

F

Depth range (zoom) buttons

Zooming the image

You can zoom the image.
The zoom level is shown on the image. If the cursor is active, the
system zooms in where the cursor is positioned.

15

DownScan

| GO XSE/XSR Operator Manual

163

«
...
161
162
163
164
165
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Laica Pages: 4

Brand: NEC Pages: 54

Brand: Panasonic Pages: 30

Brand: Haigh Pages: 60

Brand: PASCO Pages: 5

Brand: Pasco Scientific Pages: 27

Brand: PARUS Pages: 6

Brand: Sota Pages: 7

Brand: Mindray Pages: 295

Brand: ZAMST Pages: 14

BIO-FIGHTER 4Xtreme

Brand: Dust Free Pages: 8

Brand: HF Scientific Pages: 5

Brand: Lightolier Pages: 2

Brand: Mueller Pages: 2

Tractelift Type II

Brand: Tractel Pages: 28

Brand: WENVY Pages: 23

WaterLink Spin Touch DW

Brand: LaMotte Pages: 64

High End Systems SolaPix 7

Brand: ETC Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands