Simrad GO XSE Series Operator'S Manual Download Page 124 | Manualshive

Page: 124 / 242

background image

•

Disable

, closes the message dialog and cancels the dangerous

target alert for all vessels. You can re-enable the dangerous vessel
alert in the Vessels section of the Alarms settings dialog.

Ú

Note:

When Disable is selected, the Dangerous target alert

option in the Alarms settings dialog is turned off. When the
Dangerous target alert option is turned off (disabled),
dangerous target alert messages are not generated for either
radar or AIS dangerous targets.

•

Ignore

, closes the message dialog and disables the alert for that

vessel. The alert for that vessel will reappear if the status of that
vessel changes, i.e. that vessel becomes safe and then dangerous
again.

•

View

, closes the message dialog and opens the Radar panel with

the dangerous vessel’s pop-up activated. You can select the
vessel’s pop-up in the radar panel to see the vessel details.

Advanced radar options

Menu options can vary depending on your radar's capability and
the selected operation mode.

Noise Rejection

Sets the amount of noise filtering applied by the radar. Target
sensitivity is increased at longer ranges when this control is set to
Low or High, but does cause some loss of target discrimination.

Ú

Note:

To get maximum range performance from the radar,

transmit on one range only, set the Noise Reject control to High
and the threshold as low as possible. The default is 30% for less
clutter on the screen. In some areas where extreme high
interference may exist, try OFF for best radar image.

Threshold

The threshold sets required signal strength for the lowest radar
signals. Radar returns below this limit are filtered and are not
displayed.

Target expansion

Target expansion increases the length of targets in range, making
them easier to see.

124

Radar

| GO XSE/XSR Operator Manual

«
...
122
123
124
125
126
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Ecco Pages: 3

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

Brand: NANLUX Pages: 39

Brand: Rane Pages: 38

Brand: Kartsana Pages: 36

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

Brand: UNI-T Pages: 4

UPO3000E Series

Brand: UNI-T Pages: 94

Brand: Underhill Pages: 12

Brand: UMS Pages: 92

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 85

Brand: Yamaha Pages: 43

Brand: Yamaha Pages: 200

Brand: Qtx Pages: 6

Brand: Marcy Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands