Simrad GO XSE Series Operator'S Manual Download Page 90

Page: 90 / 242

The autopilot will engage in the selected mode, and the autopilot
controller will change to show active mode options.
To disengage the autopilot:

•

Select the standby button

When the autopilot is in standby, the boat must be steered
manually.

Autopilot indication

The status bar shows autopilot information as long as an autopilot
computer is connected.

Autopilot modes

The autopilot has several steering modes.

Anchor modes

In these modes the trolling motor maintains the vessel position at a
selected location.

Note:

When in anchor mode, the vessel heading can be

affected by wind or current.

The following anchor options are available:

Cursor

Navigates to cursor position, and then maintains the vessel at that
position.

Trolling motor autopilot

| GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands

Simrad GO XSE Series, Operator'S Manual

Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands