manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Internet connection

Internet usage

Some features in this product use an internet connection to
perform data downloads and uploads.
Internet usage via a connected mobile/cell phone internet
connection or a pay-per-MB type internet connection may require
large data usage. Your service provider may charge you based on
the amount of data you transfer. If you are unsure, contact your
service provider to confirm rates and restrictions.

Ethernet connection

The unit is automatically connected to the internet when
connected to an Ethernet network with internet access.

WiFi connection

Use the WiFi functionality to:

•

Connect the unit to the internet. For more information, refer to

"Wireless settings"

 on page 201.

•

Connect the unit to wireless devices such as smart-phones and
tablets. The smart-phones and tablets can then be used to
remote view and control the unit. For more information, refer to

"Remote control of the MFD"

 on page 205.

Wireless settings

Provides configuration and setup options for the wireless
functionality.

23 

Internet connection

 | GO XSE/XSR Operator Manual

201

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Raymarine i70 Installation & Operation Instructions preview
i70
Brand: Raymarine Pages: 90
MADRIX NEO Quick Start Manual & Technical Manual preview
NEO
Brand: MADRIX Pages: 12
Narcotrend Compact M Operating Instructions Manual preview
Compact M
Brand: Narcotrend Pages: 47
Eazyzap Y724 Instruction Manual preview
Y724
Brand: Eazyzap Pages: 32
Obdstar MS50 User Manual preview
MS50
Brand: Obdstar Pages: 42
Ecler MIMO4040CDN Service Manual preview
MIMO4040CDN
Brand: Ecler Pages: 108
R&S RTE Getting Started preview
RTE
Brand: R&S Pages: 121
Hantek Tablet1000 Series User Manual preview
Tablet1000 Series
Brand: Hantek Pages: 98
Macht Dental POWER CLEAN Operation Instruction Manual preview
POWER CLEAN
Brand: Macht Dental Pages: 8
PacBio Sequel Safety Manual preview
Sequel
Brand: PacBio Pages: 13
Pablo BELMONT Assembly/Installation Instructions preview
BELMONT
Brand: Pablo Pages: 4
PA A42R-316 Manual preview
A42R-316
Brand: PA Pages: 28
Parkside PFMR 1400 A1 Original Operating Instructions preview
PFMR 1400 A1
Brand: Parkside Pages: 58
Zodiac Sheer Descent Installation And Operation Manual preview
Sheer Descent
Brand: Zodiac Pages: 32
Delfield 18648-PTB Specification Sheet preview
18648-PTB
Brand: Delfield Pages: 2
Idex Vetter QuickStrut Operating Instructions Manual preview
Vetter QuickStrut
Brand: Idex Pages: 14
DC Med IFU-1701 Instructions For Use preview
IFU-1701
Brand: DC Med Pages: 2
MakAlon MK-SM03 User Manual preview
MK-SM03
Brand: MakAlon Pages: 36

Brands by name

Popular brands

Load more brands