Simrad GO XSE Series Operator'S Manual Download Page 158 | Manualshive

Page: 158 / 242

background image

Network Echosounder

Select to share transducers from this unit with other units
connected on the Ethernet network. In addition, the setting must
be selected in order to see other enabled sonar devices on the
network.
When unselected, transducers connected to this unit cannot be
shared with other units connected on the network, nor can it see
other sources on the network that have this feature enabled.
For more information about how to setup the echosounder, refer to
the separate Installation manual.

Network echosounder mode

The network echosounder mode setting selects whether only one
or multiple echosounder sources can be selected at the same time.

Ú

Note:

Single source is automatically selected if there are older

legacy echosounders on the network. You cannot change this
setting if older legacy echosounders are on the network. Multi-
source mode should be selected if no legacy echosounder is
connected to the network.

Ú

Note:

When changing the mode to multi-source you must wait

30 seconds and then power down all sources. Wait 1 minute,
then restart all connected sources.

Use network depth and temp data

The unit can share depth and temperature data from an Ethernet
networked echosounder source over the NMEA 2000 network.
Use this option to select from which Ethernet network source the
data is shared.

158

Echosounder

| GO XSE/XSR Operator Manual

«
...
156
157
158
159
160
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: ACS Pages: 56

Brand: Pall Pages: 51

Brand: ZAMST Pages: 21

Brand: Eagle Pages: 3

Brand: Mangar International Pages: 8

Brand: Malvern Instruments Pages: 30

Brand: zarges Pages: 36

FUSION APOLLO MS-WB675

Brand: Garmin Pages: 18

Brand: Rapid Shape Pages: 12

MultiFill 003-561-005

Brand: Hanskamp Pages: 20

Aesculap S4 Cervical

Brand: B. Braun Pages: 43

Dynamique Biski

Brand: Enabling Technologies Pages: 44

Brand: Bodyworx Pages: 17

Brand: Wood-mizer Pages: 59

Brand: Tandem Pages: 7

Sedeo Lite Q700M

Brand: Quickie Pages: 9

Brand: Global Pages: 13

Wensco AnPro180 Stick

Brand: G2G Lighting Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands