manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Synchronize 2D/3D chart

Links the position shown on one chart with the position shown on
the other chart when a 2D and a 3D chart are shown side by side.

Pop-up information

Determines whether basic information for panel items is displayed
when you select the item.

Grid lines

Turns on/off viewing of longitude and latitude grid lines on the
panel.

Waypoints, Routes, and Tracks

Turns on/off displaying of these items on chart panels.

Ú

Note: 

To display tracks on the chart panel, the Display option in

the Tracks dialog and the tracks option in the chart settings
dialog both have to be enabled.

52

Charts

 | GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

ACS 3200 Series Operation And Instruction Manual preview
3200 Series
Brand: ACS Pages: 56
Idex Hale Sam Operation Installation Maintenance Manual preview
Hale Sam
Brand: Idex Pages: 141
IDEAL Networks SecuriTEST IP Quick Start Manual preview
SecuriTEST IP
Brand: IDEAL Networks Pages: 8
IDEAL Networks LanTEK IV Manual preview
LanTEK IV
Brand: IDEAL Networks Pages: 5
Quick DP Series Installation And User Manual preview
DP Series
Brand: Quick Pages: 24
JDS Uniphase SmartClass E1 User Manual preview
SmartClass E1
Brand: JDS Uniphase Pages: 144
JDS Uniphase IP Video Test Option HST-3000 Instruction Manual preview
IP Video Test Option HST-3000
Brand: JDS Uniphase Pages: 14
Nasco Life/form SmartScope LF01142U User Help Manual preview
Life/form SmartScope LF01142U
Brand: Nasco Pages: 2
Tanco 1300 Series Operator'S Handbook Manual preview
1300 Series
Brand: Tanco Pages: 112
Parkside PFMR 1400 A1 Original Operating Instructions preview
PFMR 1400 A1
Brand: Parkside Pages: 58
Yetter 5000 SERIES Operator'S Manual preview
5000 SERIES
Brand: Yetter Pages: 24
Yetter 5000 SERIES Owner'S Manual & Parts List preview
5000 SERIES
Brand: Yetter Pages: 32
Zero 88 Betapack 4 User Manual preview
Betapack 4
Brand: Zero 88 Pages: 12
Zest4Leisure Horizon Arch Instructions preview
Horizon Arch
Brand: Zest4Leisure Pages: 4
Zeiss ATLAS 9000 Service Manual preview
ATLAS 9000
Brand: Zeiss Pages: 119
Zehnder Rittling ComfoFond-L Installation Manual preview
ComfoFond-L
Brand: Zehnder Rittling Pages: 32
Sanav AIS-700 Manual preview
AIS-700
Brand: Sanav Pages: 34
GE Venue 50 Basic Service Manual preview
Venue 50
Brand: GE Pages: 289

Brands by name

Popular brands

Load more brands