manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Placing EBL/VRM markers by using the cursor

1.

Position the cursor on the radar image

2.

Activate the menu

3.

Select one of the EBL/VRM markers

- The EBL line and the VRM circle are positioned according to

the cursor position.

Offsetting an EBL/VRM marker

1.

Ensure that the cursor is not active

2.

Activate the menu, select 

EBL/VRM

, then select the marker you

wish to offset

3.

Select the set offset option

4.

Position the cursor on the radar panel to set the offset position

5.

Select the save option to save your settings.

You can reset the EBL/VRM center to vessel position from the menu.

Recording radar data

You can record radar data and save the file internally in the unit, or
save it onto a storage device connected to the unit.
A recorded radar file can be used for documenting an event or an
operational error. A logged radar file can also be used by the
simulator.

Ú

Note: 

The record menu option is available if recording is turned

on in the Advanced system settings.

132

Radar

 | GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Gardena 1407 Operator'S Manual preview
1407
Brand: Gardena Pages: 13
AAON RQ SERIES Manual preview
RQ SERIES
Brand: AAON Pages: 36
FarmTek Growers Supply 109722 Manual preview
Growers Supply 109722
Brand: FarmTek Pages: 9
Haaga 677 Original Operating Instructions preview
677
Brand: Haaga Pages: 31
Waterous Pressure Governor Installation And Operation Manual preview
Pressure Governor
Brand: Waterous Pages: 53
Landi Renzo V05 Instruction Manual preview
V05
Brand: Landi Renzo Pages: 16
IBM 727 Manual Of Instruction preview
727
Brand: IBM Pages: 163
Nautilus 9NP-B7524 Series Owner'S Instructions preview
9NP-B7524 Series
Brand: Nautilus Pages: 2
Nautilus Be strong NS 700X Owner'S Manual preview
Be strong NS 700X
Brand: Nautilus Pages: 34
Nautilus BE STRONG E916 Quick Start Manual preview
BE STRONG E916
Brand: Nautilus Pages: 21
Warner Electric EM-50 Service & Installation Instructions preview
EM-50
Brand: Warner Electric Pages: 14
Gastrodomus GA600BTV Installation - Use - Maintenance preview
GA600BTV
Brand: Gastrodomus Pages: 22
EXFO FOT-930 MaxTester Manual preview
FOT-930 MaxTester
Brand: EXFO Pages: 8
GLP X4 ATOM series Instruction Manual preview
X4 ATOM series
Brand: GLP Pages: 28
TLW K01-0100 Installation Manual preview
K01-0100
Brand: TLW Pages: 2
Vari Lite VL1100 Quick Start Manual preview
VL1100
Brand: Vari Lite Pages: 14
Harman DriveRack VENU360 Quick Start Manual preview
DriveRack VENU360
Brand: Harman Pages: 4
Kalamazoo K10HS Instruction Manual preview
K10HS
Brand: Kalamazoo Pages: 4

Brands by name

Popular brands

Load more brands